Differences between SAJ Technical and SAJ Level 1
Can you say it clearly?
NaokiHello everyone!
I’m Naoki, a Japanese skier who gives skiing his all for life. I specialize in Japan’s SAJ ski tests and have helped many skiers pass.
This time's theme is...
"Difference between SAJ Level 1 and SAJ Technical" That's it!
SAJ Technical is a very narrow gateway where the qualification rate is 10 percent ahead in the national average. Of course, all levels are different and in detail there are countless differences.
So,
To everyone who has read this article,
I have been studying to get up from the SAJ Level 1 to the SAJ Technical.
“You should understand this first!”
I would like to introduce two points about 2!
That point is Cochila!
①Turn speed
Adaptation to two conditions.
So,
From now on, I will explain each one in an easy-to-understand manner!
Difference between SAJ Level 1 and SAJ Technical① Turn speed
First of all, the biggest difference is
"Turn speed" That's it!
Suddenly there is a problem!
What is the slowing factor in skiing?
The answer is "Misalignment" That's it!
Turn the board while turning means putting a brake.

If you just look at this,
It looks like you are drilling.
But think about it!
Do you not slow down when the F1 car drives on a curve?
The principle behind skiing is exactly the same: the friction caused by the direction of the → you want to move and the direction of the ski kills your speed!
In the graded badge test up to SAJ Level 1,
This “slip” was well used and a gently controlled slide was required.
However, when the SAJ Technical/SAJ Crown test comes, you will need an active and aggressive slide that is going to turn down and speed up.
To put it practically,
What is the slippage required for more than SAJ Technical?
Fast sliding with little slippage
That's it!
What kind of sliding is the sliding?
This is it!

Turns where ski tracks in the snow linger,
"Carving Turn" That's what they say.
The carving turn, unlike the shifted turn earlier,
→ the direction you want to go,
You need to align the direction of the board.
In other words...
When the direction of travel and the direction of the board are aligned, you can make turns at higher speed!
First, to maximize your turn speed, you need to master the correct carving turns, and consider your step up to SAJ Technical skills begin!
And then, to get the turnover up.
The other key 'movement of the center of mass' That's it!
People who make turns where the board runs
It always moves significantly on the board.
Those who control movement of the center of mass control the turn speed!
To put it another way,
putting body weight on the skis is shifting the point.
If I were to say the ideal,
It's best to start from the top and finish the turn at the tail.
In terms of the sole of the foot position,
- Turn entry is closer to the toes
- The end of the turn is heel closer.
That's the image I have.
Of course, there are some individual differences,
First, keep in mind the image of moving putting body weight on the skis points from roughly toes to heel during the turn, moving toward the back / behind!
While putting body weight on the skis, pull the board back / behind from the front, and release the flex to make the ski run.
The movement of the center of mass is the movement of the body,
When this body movement stops, the board also stops, resulting in a non-running turn.
To summarize,
By movement of the center of mass from front to back / behind, you release flex and increase turn speed. Conversely, without movement of the center of mass, turn speed does not increase.

I have a booster, so you’re just standing up and accelerating.
I told such jokes with a straight face,
I know a former National Demo member named 1...lol
Anyway,
SAJ Level 1 was stable, which means that it was good at equal speed, but in Prize it did not.
I think this is the difference between 1!
SAJ Level 1 vs SAJ Technical ② Adapting to snow conditions
The Price Test is clearly to see the quality of the turn.
Matched the burn conditions that day.
Is it slipping?
It is viewed much more harshly than SAJ Level 1.
Unfortunately, nevertheless,
Always the same ski edgeing, same position
There are so many skiing players who ski.
Snow quality changes daily,
It also varies depending on the ski slope.
For example...
icy surface strongly stands up ski edge,
The snow is more than usual, and it is stronger.
If you don’t get a bad deal, you will be subject to a hard assessment.
So,
“This is the right thing to do in a situation like this!”
Not that there is such a thing...
Since this is a great opportunity, I can't shake this one thing!
Introducing the three golden rules of 2!
- Don't make sudden movements!
- Don't try to force ski edge on your own!
Be conscious of this 2 on a daily basis,
With the courage of challenging in every situation, you will be cleansed!
[Summary] Difference in level between SAJ Level 1 and SAJ Technical
Now, here's the summary for this time!
- Turn speed
The key is carving element and movement of the center of mass with little deviation - Adapting to Conditions
Do not make sudden movements and do not set up ski edge yourself.
So,
This time. SAJ Level 1 A big difference in SAJ Technical. 2 I have presented you to the point!
The SAJ Technical/SAJ Crown test is a qualifying qualification for many skiers, but the difficulty rate is very high and of course it’s easy to pass!
We have a manual to the high-level skiers aiming at approval for such SAJ Technical!
Here it is!

This manual is a set of know-how to improve the “turn quality” I felt most needed before I passed SAJ Technical!
As I explained this time,
SAJ Technical cannot break without raising the basic turn itself to a level!
skiingers aiming to pass SAJ Technical,
Make sure you learn the quality of the turn needed to break through the SAJ Technical/SAJ Crown test wall!
And be careful not to get hurt,
Let us enjoy skiing in any way!
So that's it for this time!
Please watch until the end,
Thank you very much!





感想や質問があればお気軽にどうぞ!
0件のコメント